|
Member
Longin |
| |
|
| |
 |
|
|
|
|
| |
|
| | FREQUENCY AND TACHO METER >> TE FREQUENCY AND TACHOMETE >> TE FREQUENCY AND TACHO METER |
 |
|
|
|
FEATURES
1.It can measure frequency tacho line speed meter
2.EEPROM back up system
3.High-accuracy,measuring field:0.1Hz-20KHz
4. All the function can operate from the panel key |
| 1. ORDERING CODE |
 |
| 2. MODEL AND SPECIFICATIONS |
| Model |
Setting stage |
Display range |
Measuring field |
Input signal |
Measuring |
| TE-R48P41B |
1 Stage |
0.001-9999 |
0.1Hz-20KHz |
4-30V |
0.02%rdg¡À3Digit |
| TE-R72P41B |
1 Stage |
0.001-9999 |
0.1Hz-20KHz |
4-30V |
0.02%rdg¡À3Digit |
| TE-R49P62A |
2 Stage |
0.00001-999999 |
0.1Hz-20KHz |
4-30V |
0.02%rdg¡À3Digit | |
| 3.SPECIFICATIONS |
| power voltage |
AC220V¡À10% 50/60Hz |
| consumption |
¡Ü5VA (at AC 220V 50Hz) |
| display range |
6 digit:0.00001-999999 4 digit:0.001-9999 |
| Measuring field |
0.1Hz-20KHz |
| input signal |
touch input,collector input,sensor input,input resistance 5K¦¸,low calm 0-2V,high calm 4-30V |
| Measuring |
0.02%rdg¡À3Digit (mult=1 div=1) |
| over flow |
When measuring £¦#118alue came 6 digit,display"------" |
| reposition mode |
hand repositon¡¢self repostion¡¢outside add signal repostion |
| output mode |
N ¡¢F¡¢ ¡¢C¡¢ R |
| assustabt voltage |
DC 12V¡À10% 50mA max |
| Insulation intension |
Between lead electric end and bare very using metal,not connect touch |
| Insulation strength |
AC2000V,50Hz/60Hz 1min(Between lead electric end and bare very using metal,not connect touch) |
| anti-jamming |
Use noise anti-jammingsirnulatorside wave disturb:+2KV(betweenpower end)¡¢+500V(beteween input end) |
| work condition |
0-50¡æ 45%-85%RH | |
| 4.CONNECTION DIAGRAM |
|
|
| 5.THE OUTSIDE DIMENSION |
|
|
| 6. CAUTIONS |
1.The meter must be heating 15 minutes with the power on before use.
2.Use in ambient temperatures of 0¡æ to 40¡æ,humidifies of 85% R.H.
3.The meter alignment interval time is one year.
4.If the input signal is superimposed with high-frequency noise,use a High-pass filter in the input signal line.
5.Input wire should not be too long. If measured signal and meter is long, please use a 2-core shielded cable, and connect its outer shite to the LO side at a signal soure.
6.If the digit meter relay is not used for a long time. Please counect power supply once every three months, not less
than 4 hours each time. | |
|
| Hit amount£º1615 Date £º2004-10-23 ¡¾Print page¡¿ ¡¾Back¡¿ |
|
|
| |
| |
|
Home¡¡
